Samsung DMT400 series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 58

background image

4. Troubleshooting

4-3

4-2. Service Inspection Mode

4-2-1. DMT800 & DMT700 series

- Press the ‘Heavy’ + ‘Delicate’ + ‘Power’ buttons at the same time for two seconds to enter Service Inspection Mode.
- All LEDs are displayed for the

fi

rst two seconds and then Software-Ver. will be indicated.

-  You can change the mode by pressing the Normal button again. If press the Normal button in this mode, the mode will be changed to next mode.
-  If you want to activate a mode while operating the dishwasher, the door must be closed.
-  If ‘LE’ , ‘OE’, ‘tE’ error occur, enter Service Inspection Mode after resolving it.
-  Service Inspection Mode is described in the following table.

Mode

Display

Related Parts

Symptoms

Note

No.1

Ft

Drain pump
Inlet Valve
Flow Meter
Water-level sensor
Turbidity

Door open warning

Water supply Error
Low level water Error
Turbidity Error

If Door is open, Door open warning (dE) will blink.
If low level sensor is not detected, Drain is executed. Water supply will be executed when low level sensor
is detected.
If water is not fully supplied(sensing on

fl

ow-meter), the Water Supply Error (4E) will blink.

When High level sensor is not detected after water supply was done, Low-level water error (9E) will blink.
When Turbidity problem is occurred after water supply was done, Turbidity Error (AE) will blink.
If all functions in this mode are completed, ‘Ft’ and ‘3.6~3.9’ will blink.

No.2

Lc

Circulation Motor

A nozzle does not inject
water.

If Low Level sensor is detected before Circulation Motor is operating, ‘LL’ and ‘Lc’ will blink.
When water is

fi

lled enough, Circulation Motor -2(190W) will be operated.

No.3

Ld

Circulation Motor

A nozzle does not inject
water.

If Low Level sensor is detected before Circulation Motor is operating, ‘LL’ and ‘Ld’ will blink.
When water is

fi

lled enough, Circulation Motor- 1(150W) will be operated.

No.4

Hd

Circulation Motor
Heater
Thermistor
Dispenser

Heater Error

If Low Level sensor is detected before Circulation Motor is operating, ‘LL’ and ‘Hd’ will blink.
When water is

fi

lled enough, Circulation Motor 1(150W) and Heater will be operated.

‘Temperature[

˚

C]’ and ‘Hd’ will blink.

When the temperature meet 60

˚

C or above, the heater is turned off.

If Heater or Thermistor have problems, the Heater Error (HE) will blink.
Dispenser will operate during 130 seconds only one time.

No.5

SH

Half Load Motor

Half load function Error

If Low Level sensor is detected before Circulation Motor is operating, ‘LL’ and ‘SH’ will blink.
When water is

fi

lled enough, Half Load Motor will be operated, and then Half load function will be operated.

No.6

SP

Half Load Motor

Storm wash function
Error

If Low Level sensor is detected before Circulation Motor is operating, ‘LL’ and ‘SP’ will blink.
When water is

fi

lled enough, Half Load Motor will be operated, and then Storm wash function will be

operated.

No.7

dF

Dry Fan Motor
Dispensor

The Dry Fan motor does
not work.

Operate the Dry Fan Motor and check whether Rinse aid is

fi

lled or not.

If there is not rinse aid in Dispenser, Rinse Re

fi

ll lamp is ON.

«
...
34
35
36
37
38
...
»

Содержание DMT400 series



























































Отзывы:

Нет отзывов

Похожие инструкции для DMT400 series

Spacemaker DSKS333EC

Бренд: GE Страницы: 3

Бренд: Gaggenau Страницы: 72

Бренд: Euromaid Страницы: 33

Бренд: ZANKER Страницы: 40

Бренд: Gaggenau Страницы: 104

Бренд: Thermador Страницы: 66

Бренд: Asko Страницы: 32

WA80CG4545 Series

Бренд: Samsung Страницы: 48

Бренд: Haier Страницы: 64

Бренд: inventum Страницы: 88

Бренд: inventum Страницы: 112

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 1

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды