Samsung DMT400 series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 58

background image

3-15

3. Disassembly and Reassembly

Part

Photo

Description

Bracket front lower

Preparation:

* Make sure to disconnect the power & water supply &

drain hose connections.

* Remove the upper & lower baskets in the dishwasher.
* Pull out the dishwasher & Lay down the dishwasher

on its back carefully.

* Remove the water supply line(& elbow).

Caution

Make sure to close the faucet before removing the
water supply line.

1. Remove the cover PCB and pull out case PCB

without disconnecting wire connectors.

- When remove case PCB, lift up two(2) clasps using

fl

at screwdriver as lever effect.

2. Pull out the case PCB and

fi

x it using standard duct

tape like as picture.

3. Remove the four (4) screws on both sides of the

bracket front lower.

4. The bracket front lower is

fi

xed with the guide wire

with three hooks.
Use a long nose pliers or

fl

at screwdriver.

5. Using a Philips screw driver, lift up the each clasp on

both sides of the bracket front lower.

6. To remove the bracket front lower entirely, push inside

and pull out outer surface holding each sides. (refer
the pictures.)

坍

Reassembly is in the reverse order of the removal.

«
...
23
24
25
26
27
...
»

Содержание DMT400 series



























































Отзывы:

Нет отзывов

Похожие инструкции для DMT400 series

Washing Machine

Бренд: BALAY Страницы: 8

Бренд: Samsung Страницы: 5

Бренд: elvita Страницы: 158

Бренд: NEFF Страницы: 48

Бренд: BorMann Страницы: 14

Бренд: Zline Страницы: 28

Бренд: BALAY Страницы: 56

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 68

Бренд: Samsung Страницы: 80

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 220

Бренд: Samsung Страницы: 316

Бренд: Electrolux Страницы: 27

Бренд: Electrolux Страницы: 23

Бренд: Electrolux Страницы: 23

Бренд: Electrolux Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды