Samsung DMT400 series Скачать руководство пользователя страница 50

Страница: 50 / 58

4. Troubleshooting

4-17

Error type

Error mode

Checking Method

Corrective actions

Dry is not satis

ed.

None

1. Check whether Rinse Re

ll LED light or not.

- If Rinse Re

ll LED light, re

ll rinse in Dispenser.

2. Check the wire connections for the Dry Fan Motor.

- Reconnect the Dry Fan Motor connectors.

3. Check the resistance of the Dry Fan Motor coil.

(Remove the connector before measuring.)

Normal: Approx. 80

- Faulty: Replace the Dry Fan Motor assy.

4. Check the resistance of the Thermal Actuator.

(Remove the connector before measuring.)

Normal: Approx. 73

- Faulty: Replace the Main PBA assy.
- Check

voltage

5. Check the operation of the Dry Fan Motor Relay
: Check the operating voltage between the yellow wire of the

C101 connector and the sky wire of the CN201 connector.

Normal: 120V (while operating)

- Faulty: Replace the Main PBA assy.
- Remove

retainer.

- Check

voltage.

6. Check the operation of the dispenser.

If rinse aids are not dispensed, a dry error may occur.

Because the dishes are heated and heat dried during the last
drying cycle, the dried state of plastic dishes may not be
optimal

- See “Detergent is not dispensed”

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды