Samsung DMT400 series Скачать руководство пользователя страница 28

Страница: 28 / 58

3-18

3. Disassembly and Reassembly

Part

Photo

Description

Distributor Motor

(DMT800 /

DMT700 )

The distributor motor is located under the tub at the middle, rear the circulation motor. The
distributor motor operates to select

ow direction at the dishwasher sump when select half load

or storm wash option.

Preparation:

Disassemble the cover sump & case scroll.

Refer the “cover sump” disassembly section.

Disassemble the shutter.

Refer the “shutter” disassembly section.

Remove the distributor motor connector.

Remove the two (2) screws that hold the

distributor motor in place.

Pull out the distributor motor and micro switch
holding by hooks.

Be careful removing it because it has cam-switch
and a seal in opposite side.

Circulation

Motor

Preparation:

Disassemble the cover sump & cutter disposer and
shutter.

Refer the each disassembly section.

Remove the circulation motor and capacitor

connection.

Remove the four(4) screws holding the circulation

motor and the sump in place,and the one(1) screw
for earth connection from main wire-harness.

Hold and pull out the circulation motor carefully to
remove it from the sump.

Caution

Make sure to remove remain water in the
dishwasher. If not, wet the

oor.

Caution

Be careful don’t break oil seal when removing them.

坍

Reassembly is in the reverse order of the removal.

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды