Samsung DMT400 series Скачать руководство пользователя страница 48

Страница: 48 / 58

4. Troubleshooting

4-15

Error type

Error mode

Checking Method

Corrective actions

The Cycle does not
start.

None

1. Check the connections for the Door Sensing Switch

: Check the blue wire and the switch connected to the
blue wire.

Normal (Power Key On): 9.5 to 12.5V (when the

door is open)

Normal (Power Key Off): 5.5 to 7.0V (when the

door is open)

Normal : <2V (when the door is closed)

- Reconnect the Door Sensing Switch connectors

2. Check the operation of the Door Sensing Switch.

(Remove the connector before measuring.)
: Check the blue wire and the switch connected to the
blue wire.

Normal: OPEN (when the door is open)

Normal: SHORT (when the door is closed)

- Faulty: Replace the Door Sensing Switch.
- Normal: Replace the Main PBA assy.

No Washing

None

1. Check whether the nozzle injects water normally.

- See “The nozzle does not inject water”.

2. Check the operation of the Heater.

- See “Heater Error”.

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды