Samsung DMT400 series Скачать руководство пользователя страница 15

Страница: 15 / 58

3-5

3. Disassembly and Reassembly

Part

Photo

Description

Control Panel

Window Panel

(DMT800)

Preparation:
* Disassemble the frame front , Assy control panel

and Door lock switch.

- Refer the “Frame front” disassembly section to

separate the Frame front.

1. Remove the two(2) screws on the control panel

and release the window panel using

at screw

driver.

- Insert the

at screw driver into the gap of screw

boss and turn it over.

2. Rotate the window panel to upside and

disconnect the wire connector.

3. Release the two(2) screws on the window panel

to release the guide LED.

Control Panel

(DMT400)

Preparation:
* Disassemble the frame front , Assy control panel

and Door lock switch.

- Refer the “Frame front” disassembly section to

separate the Frame front.

1. Remove two(2) connectors in the display – PCB.

2. Pull the control panel up slightly from Assy frame

front , and pull it out.

3. Unscrew two(2) screws to remove display-PCB

and guide-LED.

4. Disconnect the 2 wire connectors from control

panel(touch-PCB).

坍

Reassembly is in the reverse order of the removal.

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды