68 | SAMLEX AMERICA INC.
SECTION 4 |
Parameter Setup
4.4.2.20.1 Programming Steps for Parameter “ABSORP EXIT AMPS”
ð
ð
E V O - 1 2 1 2 F
I n v e r t i n g
A C
o u t p u t :
1 2 0 . 0 V
< 0 . 1 0 A
6 0 . 0 0 H z
Enter Key
Enter Key
Any Operating Mode Screen from
Fig 3.1 to 3.8
[Above screen is Screen 1 of Fig 3.2(a)]
Password 8052
See Section 4.3.1
See Table 4.3, Parameter Setup
Screen No. 20 for
programmable range
S e l e c t
G r o u p
*
C H A R G E
C U R V E
ð
S e l e c t
P a r a m e t e r
C H A R G E
C U R V E
*
B U L K C U R R E N T
2 0 A
ð
S e l e c t
P a r a m e t e r
C H A R G E
C U R V E
*
A B S O R P
E X I T
A M P S
4 A
S e l e c t
P a r a m e t e r
C H A R G E
C U R V E
*
A B S O R P
E X I T
A M P S
4 A
Enter Key
Down Key x 19 times
P a s s w o r d
k e y
i n
0 0 0 0
ð
Enter Key
4.4.2.21 CHARGING PROFILE
(Table 4.3, Parameter Setup Screen No. 21)
Parameter “CHARGING PROFILE” provides 6 options for Charging Profiles that are designed to cover various charging
requirements for Lead Acid, Nickel-Zinc (Ni-Zn) and Lithium Ion Batteries.
i
INFO
7th Charging Profile i.e. 4-Stage Adaptive Charging Profile for Equalization is also available and can be activated
at any time during charging taking place under 1 of the 6 Charging Profile options given at Table 4.5.
Procedure
to activate 4-Stage Adaptive Charging Profile for Equalization is described under programming parameter
“EQUALIZE- 4 STAGES” at Section 4.4.2.12
The 6 options under parameter "CHARGING PROFILE" are as follows:
• 0 = 3 Stage Adaptive (Default)
• 1 = 3 Stage Type 1
• 2 = 3 Stage Type 2
• 3 = 2 Stage Type 1
• 4 = 2 Stage Type 2
• 5 = 2 Stage Type 3
NOTE:
3-Stage Adaptive Charging Profile option “0 = 3 Stage Adaptive
(Shown as “0=3 Stg Adaptive” in the
programming screen)
” is the default charging profile applicable for Lead Acid Batteries
Details of the 6 programmable charging profiles under programming parameter “CHARGING PROFILE” are given in TABLE 4.5.
!
CAUTION!
Some Battery Management Systems (BMS) for Lithium Ion Batteries may come with protections against over-charge
/ over-discharge / over-temperature that will require control over charging and discharging of the Lithium Ion battery.
For this, any of Pins 1/2/3/4 and 5/6/7/8 of the RJ-45 Jack marked "Battery Temp Sensor" on the front panel of the
EVO
TM
Inverter/Charger (6, Fig 2.1 of Owner's Manual for EVO
TM
Inverter/Chargers) may be used to feed potential free
contact closing signal from the BMS to “Stop Charging” or “Stop Inverting”
(Refer to Section 4.4.2.22.2 for details)
!
ATTENTIONS!
Certains systèmes de gestion de batterie (BMS) pour batteries au lithium-ion peuvent être dotés de protections
contre la surcharge / sur-décharge / surchauffe qui nécessiteront un contrôle de la charge et de la décharge de
la batterie au lithium-ion. Pour cela, l’un des broches 1/2/3/4 et 5/6/7/8 de la prise RJ-45 marquée "Battery Temp
Sensor" sur le panneau avant de l'onduleur / chargeur EVO
TM
(6, Fig 2.1 of Owner's Manuel pour les onduleurs /
chargeurs EVO) peut être utilisé pour alimenter le signal de fermeture de contact libre de potentiel du système de
management jusqu'à "Stop Charging" ou "Stop Inverting"
(Voir la section 4.4.2.22.2 pour plus de détails)
Содержание EVO-RC-PLUS
Страница 127: ...SAMLEX AMERICA INC 127 NOTES ...