manualshive.com logo in svg

Ruskin TDP05K, Технический бюллетень, Страница: 24 / 36

Поделиться
Скачать
Ruskin TDP05K Скачать руководство пользователя страница 24

TDP05K Advanced Thermal Dispersion Probe Airflow Measuring System Technical Bulletin

Release Date: 06/2022

Page 24

Modbus RTU Network Configuration

The Modbus RTU Network Configuration sub-menu turns Modbus RTU on or off and configures parameters based on the Modbus RTU 

type.

Selected Submenu

Submenu Selections

Submenu Selection Display

Figure 16: Modbus RTU Network Configuration Flowchart

Modbus RTU Network 

Configuration Submenu 

Selections 

Configurable Options

Modbus On/Off 

Select On or Off.

Modbus Address 

Select a value between 1 and 247. Holding down the button increases the rate the value updates.

Modbus Baud Rate 

Select baud rate of 9600, 19200, 38400 (default), 57600, 76800, or 115200.

Modbus Parity 

Select ODD, EVEN (default), NONE1 (one stop bit), or NONE2 (two stop bits).

Float Order 

Select Little Endian (default) or Big Endian.

String Order 

Select Normal (default) or Swapped.

Table 15: Modbus RTU Network Configuration Submenu Selections and Configurable Options 

Firmware Note:

 Only 

ONE

 Network output configuration can be active at a time.

- Modbus RTU (Default On)
- BACnet (Default Off)

Содержание TDP05K





































Отзывы:

Нет отзывов