Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 3

Страница: 3 / 123

Contents

Preface..........................................................................................................................................................................................................7

Document Conventions..........................................................................................................................................................................7

Notes, Cautions, and Warnings.......................................................................................................................................................7

About This Document..................................................................................................................................................................................11

Supported hardware and software....................................................................................................................................................... 11
What's new in this document............................................................................................................................................................... 12

Device Overview..........................................................................................................................................................................................13

Preparing for the Installation........................................................................................................................................................................ 21

Safety precautions............................................................................................................................................................................... 21

Facility requirements.............................................................................................................................................................................23
Quick installation checklist....................................................................................................................................................................24

Pre-installation tasks..................................................................................................................................................................... 24
Installation and initial configuration................................................................................................................................................ 24

Shipping carton contents..................................................................................................................................................................... 26

Mounting the Device....................................................................................................................................................................................27

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды