manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 53

FIGURE 32 Installing a 24-port or 48-port device in a two-post rack

1. Rack-mounting screws

2. Cage nuts

6. If installing multiple devices, mount them in the rack, one below the other with the heaviest device at the bottom and lightest

device on the top.

Installing the 1U, 1.5U, and 2U Universal Kit for Four

Post Racks (XBR-R000295)

Use the following instructions to install a 1U, 1.5U, or 2U device in a 19-in. (48.3 cm) EIA rack using the 1U, 1.5U, and 2U Universal Kit for
Four Post Racks (XBR-R000295). Any updates to these instructions will be added to the hardware installation guide for your product.

Mounting the Device

Installing the 1U, 1.5U, and 2U Universal Kit for Four Post Racks (XBR-R000295)

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

53

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды