Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 100

Страница: 100 / 123

TABLE 26 Temperature thresholds (continued)

Model

Low limit temperature

High limit temperature

Critical (shutdown) temperature

PoE PSU: 49°C (120°F)

PoE PSU: 57°C (135°F)

ICX 7150-48PF

85°C (185°F)

PoE PSU: 34°C (93°F)

95°C (203°F)

PoE PSU: 41°C (106°F)

105°C (221°F)

ICX 7150-48ZP

85°C (185°F)

PoE PSU: 34°C (93°F)

95°C (203°F)

PoE PSU: 41°C (106°F)

105°C (221°F)

To display the temperature of a device, enter the

show chassis

command at any level of the CLI. The

show chassis

command displays the

current temperature, the power supply status, and temperature threshold levels. The displayed temperature reflects the temperature of the
board inside the device.

device# show chassis

The stack unit 1 chassis info:

Power supply 1 (AC - PoE) present, status ok

Model Number: YM-1921AB06R

Serial Number: SA000V171708000081

Firmware Ver: P2H802A00

Power supply 1 Fan Air Flow Direction: Front to Back

Power supply 2 (AC - PoE) present, status ok

Model Number: YM-1921AB06R

Serial Number: SA000V171708000083

Firmware Ver: P2H802A00

Power supply 2 Fan Air Flow Direction: Front to Back

Fan 1 ok, speed (manual): 1<->[[2]]

Fan 2 ok, speed (manual): 1<->[[2]]

Fan controlled temperature:

Rule 1/2 (MGMT THERMAL PLANE): 60.7 deg-C

Rule 2/2 (PoE THERMAL PLANE): 10.0 deg-C

Fan speed switching temperature thresholds:

Rule 1/2 (MGMT THERMAL PLANE):

Speed 1: NM<----->95 deg-C

Speed 2: 85<----->105 deg-C (shutdown)

Rule 2/2 (PoE THERMAL PLANE):

Speed 1: NM<----->41 deg-C

Speed 2: 34<----->105 deg-C (shutdown)

Fan 1 Air Flow Direction: Front to Back

Fan 2 Air Flow Direction: Front to Back

Slot 1 Current Temperature: 61.7 deg-C (Sensor 1), 54.4 deg-C (Sensor 2), 10.0 deg-C (Sensor 3)

Slot 2 Current Temperature: NA

Warning level.......: 102.0 deg-C

Shutdown level......: 105.0 deg-C

Boot Prom MAC : 609c.9fe2.154c

Management MAC: 609c.9fe2.08d6

Monitoring the Device
Monitoring power and cooling

Ruckus ICX 7150 Switch Hardware Installation Guide

100

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды