manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 94

Status mode LEDs

You must press the status mode selection button to select the status mode to display the corresponding status on the individual port status
LED. Pressing the button once shifts to the next mode in the following sequence:

1. Port link status mode (STAT) (default mode)

2. Port speed status mode (SPD)

3. Member ID status mode (ID)

4. USB status mode (USB)

5. PoE status mode

NOTE
When in USB mode, pressing the status mode selection button for more than 5 seconds initiates the copy files such as the
image/manifest file, configuration file, and Show Tech (supportsave) from the device to the USB.

Port status mode (STAT) LED

The port status mode (STAT) LED displays the link status and activities of each port. Each unit within the stack will also display the local port
status.

Refer to the following table to interpret the port status mode LED.

TABLE 13 Port status mode (STAT) LED during normal operation

LED color

Status of hardware

Recommended action

Off

The port does not have a valid link.

None.

Steady green

The link is up and there is no traffic.

None.

Flashing green

The link is up and traffic/packets are transmitted
or received.

None.

Steady amber

In Error or Out Error.

None.

Clear stats

 CLI impacts the steady amber state, if

no more error port moves out of the steady
amber state.

Flashing amber

UDLD/LACP Blocking/ERR-DIS.

None.

Port speed status mode (SPD) LED

Port speed status (SPD) mode displays the speed setting of each downlink and uplink port (including modules).

Refer to the following table to interpret the port speed status mode LED.

TABLE 14 Port speed status (SPD) LED during normal operation

LED color

Status of hardware

Recommended action

Off

There is no valid link.

None.

Steady green

Highest speed.

None.

Flashing green

Second highest speed.

None.

Steady amber

Third highest speed.

None.

Flashing amber

Fourth highest speed.

None.

Alternating amber and green

Fifth highest speed.

None.

Monitoring the Device
Interpreting port-side LEDs

Ruckus ICX 7150 Switch Hardware Installation Guide

94

Part Number: 53-1004928-05

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды