Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 55

Страница: 55 / 123

FIGURE 33 Rack kit parts

Front brackets (2)

Bracket extensions (2)

Rear brackets, short (2)

Rear brackets, medium (2)

Rear brackets, long (2)

Screw, 8-32 x 5/16-in., panhead Phillips (8)

Screw, 8-32 x 5/16-in., flathead Phillips (16)

Screw, 6-32 x 1/4-in., panhead Phillips (8)

Screw, 10-32 x 5/8-in., panhead Phillips (8)

10.

Retainer nut, 10-32 (8)

Ensure that the items listed and illustrated are included in the kit. Note that not all parts may be used with certain installations depending on
the device type.

CAUTION
Use the screws specified in the procedure. Using longer screws can damage the device.

Flush-front mounting the device in the rack

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

NOTE
Illustrations in these rack installation procedures are for reference only and may not show the actual device that you are installing.

Mounting the Device

Flush-front mounting the device in the rack

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды