Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 58

Страница: 58 / 123

4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 35 Attaching the bracket extensions to the device

Bracket extensions

Screws, 8-32 x 5/16-in., flathead Phillips

Installing the device in the rack

Complete the following steps to install the device in the rack.

1. Position the device in the rack, as shown in

Figure 36

, providing temporary support under the device until the rail kit is secured to

the rack.

2. Attach the right front bracket to the right front rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the

upper and lower holes in the bracket.

3. Attach the left front bracket to the left front rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the

upper and lower holes in the bracket.

Mounting the Device
Flush-front mounting the device in the rack

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды