manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 32

FIGURE 15 Attaching the logo side of the magnet sheet to the bottom panel of the compact device

Mounting the device on a metal surface or metal wall

CAUTION
Do not mount the device on a surface with the top panel facing downward. Mount the device only on a vertical metal surface with
the front panel port-side facing downward.

CAUTION
Ensure that the metal surface is flat and the texture is smooth to hold the device strongly. Check for other conditions that might
impede secure magnetic mount.

Complete the following steps to securely mount a compact device on a metal surface or metal wall:

1. Ensure that the magnet sheet is attached to the bottom panel of the device. Refer to 

Attaching the magnet sheet to the device

 on

page 31.

Mounting the Device
Mounting the compact device with a magnet

Ruckus ICX 7150 Switch Hardware Installation Guide

32

Part Number: 53-1004928-05

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды