manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 31

Before mounting the device to a metal surface using the magnet sheet, ensure that the following requirements are met:

•

The magnet sheet is attached to the bottom panel of the device. Refer to 

Attaching the magnet sheet to the device

 on page 31.

•

Ensure that the device is not installed more than 110 mm. above the floor.

Note the following important installation considerations before installing the device on a metal surface using the magnet mount:

•

The strength of the magnet will vary depending on the surface it is used on.

•

The magnet’s force might weaken over time. Check the strength of the magnet regularly for about one year. Move the device up
and down and confirm the magnet strength.

When adequate ventilation is provided and the magnet is attached to the device, you can securely mount the device in the following
locations:

•

A metal wall or metal surface. Refer to 

Mounting the device on a metal surface or metal wall

 on page 32.

•

Underneath a metal desktop. Refer to 

Mounting the device under a metal desk

 on page 34.

Attaching the magnet sheet to the device

Before mounting the device to a metal surface, place the logo side of the magnet sheet (displaying the Brocade logo) squarely against the
bottom panel of the device to attach the device to the magnet sheet.

CAUTION
The magnet sheet can only be placed against the bottom panel of the device. Do not attempt to attach the magnet sheet to any
other panels on the device.

CAUTION
Before mounting the device using the magnet sheet, make sure the rubber feet are not installed on the device to ensure that the
magnet sheet holds on to the device strongly and does not detach. If the rubber feet are already installed, remove them first
before attaching the magnet sheet.

Mounting the Device

Mounting the compact device with a magnet

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

31

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды