manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 85

FIGURE 56 UTP crossover cable

•

Straight-through UTP cabling is required for direct UTP attachment to workstations, servers, or routers using network interface
cards (NICs). Fiber-optic cabling is required for direct attachment to Gigabit NICs or switches and routers through fiber ports.

FIGURE 57 Straight-through cable

•

All 10/100 and 1000 Mbps Ethernet copper ports on the devices support automatic Media Dependent Interface (auto-MDI) or
automatic Media Dependent Interface Crossover (auto-MDIX) detection. Auto-MDI or auto-MDIX is enabled on all 10/100 and
1000 Mbps copper ports by default. For each port, you can disable auto-MDI or auto-MDIX, designate the port as an MDI port, or
designate the port as an MDIX port.

Installing Transceivers and Cables

Installing the Ethernet RJ-45 cables

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

85

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды