manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 30

FIGURE 14 Attaching the adhesive feet on a 24-port or 48-port device

1. Attach the four adhesive feet to the bottom of the device. If installing multiple devices, attach the adhesive feet to each device.

2. Set the device on a flat desktop, table, or shelf near an AC power source. Make sure that adequate ventilation is provided for the

system. A 7.62 cm (3 in.) clearance is recommended on each side.

3. If installing multiple devices, place each device squarely on top of the one below. If you have both compact devices and regular

devices, place the regular devices at the bottom.

4. Power on the system.

Mounting the compact device with a magnet

CAUTION
Ensure that adequate ventilation is provided for the system. A 3 cm clearance is recommended above the device and 8 cm
clearance is recommended on each side.

CAUTION
When magnet mounting a switch, do not install it in a position where it can easily become unstable and fall, causing injury or
damage to the switch.

Use the magnet-mount kit to mount the device on a metal wall or a metal surface, including underneath a metal desk. The magnet-mount
kit is available for order separately from the device and consists of a single magnet sheet.

Mounting the Device
Mounting the compact device with a magnet

Ruckus ICX 7150 Switch Hardware Installation Guide

30

Part Number: 53-1004928-05

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды