manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 21

Preparing for the Installation

•

Safety precautions...................................................................................................................................................21

•

Facility requirements................................................................................................................................................23

•

Quick installation checklist.......................................................................................................................................24

•

Shipping carton contents........................................................................................................................................ 26

Safety precautions

When using this product, observe all danger, caution, and attention notices in this manual. The safety notices are accompanied by symbols
that represent the severity of the safety condition

Refer to Cautions and Danger Notices at the end of this guide for translations of safety notices for this product.

General precautions

DANGER

The procedures in this manual are for qualified service personnel.

DANGER

Before beginning the installation, see the precautions in “Power precautions.”

DANGER

The equipment ports are intra-building type and must not be directly connected to metallic outside plant (OSP) cable conductors.

CAUTION
Changes or modifications made to this device that are not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.

CAUTION
Make sure the airflow around the front, and back of the device is not restricted.

CAUTION
Never leave tools inside the chassis.

CAUTION
To protect the serial port from damage, keep the cover on the port when not in use.

CAUTION
Do not install the device in an environment where the operating ambient temperature might exceed 45°C (113°F).

ESD precautions

DANGER

For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

21

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды