RR Mechatronics EHST109621 Скачать руководство пользователя страница 96

Страница: 96 / 134

E9: Air flow failure!

ESR analyser unit was not able to

get a stable reading during the

vacuum test before aspiration the

sample.

•

Check for leakage on the

pipette or fill nozzle.

E10: Sample probe was jammed.

Check both needles before

sampling!

Sample probe was probably

jammed when going down and

exceeded the maximum current

level.
Sample probe went back to its

home position after the error.

•

Check if outer needle is

clogged up with rubber.

•

Sample probe maybe bend.

E11: Sample probe not on position

(going down)! Timeout error!

Sample probe did not go down

within a certain time limit.

•

Sample probe motor is faulty.

•

Sample probe motor driver on

needle board is faulty.

•

Sample probe is blocked.

E12: Dilution error: wrong or no

diluent flow. Check the diluter!

Diluter malfunction

•

Check diluent flow sensor

•

Check tubes diluter system

E13: Fillnozzle not in home

position!

Fill nozzle did not reach the Home

position within a certain time limit.

•

Fill nozzle motor is faulty.

•

Fill nozzle motor driver on

nozzle board is faulty.

•

Fill nozzle is blocked.

E14: Outer needle motor position

error! (home)

Outer needle did not reach the

home (top) sensor within a certain

time limit.

•

Check home (top) sensor.

•

Outer needle motor is faulty.

•

Outer needle motor driver on

needle board is faulty.

•

Outer needle is blocked.

E18: Carousel position error!

Check Rinse position.

Value of potentiometer does not

match the value stored in memory

of the current rinse position.

•

Check if the rinse position is

right.

•

Set correct rinse position and

perform a "Learn carousel

position".

•

Check mechanical connection

potentiometer.

E19: Drive motor timeout!

Drive motor did not move or motor

is blocked

•

Check the home sensor

•

Motor is faulty

•

Motor driver on drive board is

faulty

E22: Waste bottle full!

Empty waste bottle and clear error. •

Check level sensor.

E23: "Fill " sensor out of range.

Check/clean this sensor !

The Fill sensor has reached a

critical level.
Continuing could result in filling

errors.

•

Check and/or clean the Fill

sensor. If cleaning fails, replace

sensor

Appendix for Interrliner

MRN-164_2-EN Version 2.02 Interrliner

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды