RR Mechatronics EHST109621 страница 101 Скачать руководство пользователя

Страница: 101 / 134

E181: Barcode rotator up / down

motor timeout!

The Barcode vertical motor didn’t

reach its up or down position

within a certain time limit.

▪

Check up and down sensors.

▪

Faulty Barcode vertical motor.

▪

Barcode rotator unit

mechanically blocked.

▪

Broken wire to barcode

vertical motor.

▪

Faulty Barcode vertical motor

driver on Indexer board.

E182:

E183: Indexer motor timeout!

The indexer didn’t reach its

position within a certain time limit.

▪

Fuse was triggered.

▪

Faulty indexer motor.

▪

Indexer mechanically

blocked.

▪

Broken wire(s) to indexer

E184: Indexer error: barcode

rotator not in up position!

The indexer could not move to a

new position, because the barcode

rotator was not in its up position.

▪

Check Barcode rotator up /

down motor.

▪

Check sensors of Barcode

rotator up / down unit.

E185: Indexer error: elevator

platform not in back position!

The indexer could not move to a

new position, because the elevator

platform was not in its back

position.

▪

Check platform slider motor.

▪

Check home sensor of

platform unit.

E193: Elevator motor timeout!

The elevator didn’t reach its

position within a certain time limit.

▪

Fuse was triggered.

▪

Faulty lift motor.

▪

Elevator mechanically

blocked.

▪

Broken wire(s) to lift motor.

▪

Faulty lift motor driver on

Elevator board.

E194: Tube unit front / back motor

timeout!

The platform slider didn’t reach the

front or back position within a

certain time limit.

▪

Check platform home and

front sensors.

▪

Faulty platform slider motor.

▪

Platform unit mechanically

blocked.

▪

Broken wire to platform slider

motor.

▪

Faulty platform slider motor

driver on Elevator board.

Appendix for Interrliner

MRN-164_2-EN Version 2.02 Interrliner

101

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды