RR Mechatronics EHST109621 страница 97 Скачать руководство пользователя

Страница: 97 / 134

E24: "Diluter Start" sensor out of

range. Check/clean this sensor !

The Diluter Start sensor has

reached a critical level.
Continuing could result in filling

errors.

•

Check and/or clean the

Diluter Start sensor. If cleaning

fails, replace sensor

E25: "Measure" sensor out of

range. Check/clean this sensor !

The Measure sensor has reached a

critical level.
Continuing could result in wrong

ESR results.

•

Check and/or clean the

Measure sensor. If cleaning

fails, replace sensor

E26: "Diluent Flow" sensor out of

range. Check/clean this sensor !

The EDTA Flow sensor has reached

a critical level.
Continuing could result in filling

errors.

•

Check and/or clean the EDTA

Flow sensor. If cleaning fails,

replace sensor

E27: "Temperature" sensor out of

range. Check Settings !

The measured room temperature

has reached a critical level.
Continuing could result in wrong

ESR results.

•

Check the temperature

sensor setting.

•

Check and/or clean the

Temperature sensor. If cleaning

fails, replace sensor

E29: Result path not found.

Switched to default (D:\). Check

"Result Path" setting.

Selected result path is not valid.

Software is using the default

setting

•

Check result path setting

•

Check if network or USB

devices are used.

E30: No ACK/NACK received from

host after sending inquiry!

No response from Host within a

certain time limit after sending an

inquiry 3 times.

•

Check communication cable

between Host and Interrliner

computer.

•

Check serial port settings

(baud rate, etc...)

•

Check protocol settings.

•

Check Host computer.

E31: NACK received from host

after sending inquiry!

Did not receive ACK from Host

after sending inquiry 3 times.

See E30

E32: LIMS Connection timeout.

Host not found!

The ESR analyser unit could not

establish a connection with the

HOST (server) via TCP/IP.

•

Check TCP/IP settings

•

Check network cable

•

Check HOST settings

E34: No response from host after

sending 'Sample data record'!

No response from Host within a

certain time limit after 3 attempts.

See E30

E35: No response from host after

sending 'Sample flag record'!

No response from Host within a

certain time limit after 3 attempts.

See E30

E36: No ACK/NACK received after

sending 'Sample result string'!

No response from Host within a

certain time limit after 3 attempts.

See E30

Appendix for Interrliner

MRN-164_2-EN Version 2.02 Interrliner

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды