RR Mechatronics EHST109621 Скачать руководство пользователя страница 123

Страница: 123 / 134

Clean waste separator and exchange Waste cassette assembly
Be careful, as there may be blood in the cassette. First, make up some disinfectant and put this in the

waste separator. Press

Prime Disinfectant

to pump disinfectant through the pump cassette.

Clean Separator
The waste system must be cleaned before replacing the waste

pump cassette.

1. Open the left cover and remove the waste container. The

waste separator is now visible.

2. Lift the stainless steel vacuum tube with use of the lever.
3. Pull the waste separator towards the front of the ESR

analyser unit. (Note: The separator has two sensor connectors

at the rear)

4. Remove bacterial HEPA filter.
5. Fill waste separator with 100ml disinfectant or 100 ml water

with 2% bleach.

6. Replace bacterial HEPA filter.

7. Lift left cover.

8. Lift stainless steel vacuum tube up.
9. Insert the waste separator sliding it over the support shelf.

10. Push the waste separator towards the rear, with the sensor

connectors in the holes.

11. Release the stainless steel vacuum tube.
12. Replace the waste container.
13. Close left cover.

Work instruction Interrliner

MRN-164_2-EN Version 2.02 Interrliner

123

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

RR Mechatronics EHST109621, Инструкция по эксплуатации, Страница: 123 / 134

Результаты поиска

Содержание EHST109621

Отзывы: