RR Mechatronics EHST109621 страница 121 Скачать руководство пользователя

Страница: 121 / 134

6. Place one end of the tube in the pump plate holder.

7. Pull the new tube over the peristaltic pump rotor.

8. Pull pump tube slightly downwards and at the same time towards the back of the Interrliner.

Fill and clean

Starrsed Cleaning Agent preparation Interrliner ESR analyser unit: Fill

and clean:

This cycle takes about 90 minutes.

1. Fill the clean adapter EHST110907 with hot de-ionized water. (+/-

150 ml, 80 °C)

2. Add 15 ml Starrsed Cleaning Agent (QRR 010905) to the hot

water in the adapter.

3. Place the cap on the adapter and mix well.
4. Put the adapter with cleaning solution on the lower tube holder.
5. Select

Maintenance

tab,

Prime/Clean

, button

Fill and clean

Start Fill and clean procedure:

Work instruction Interrliner

MRN-164_2-EN Version 2.02 Interrliner

121

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды