rotork CML-100, Инструкция по установке и обслуживанию

Страница: 55 / 60

A4 US
US
A4
US
A4
A4 US
55
Redefining Flow Control
Advanced Menu
8 spLTRg -spLIT RAnge opeRATIon
MInCMd - Minimum Split Range Command Select value
of 4 to 20 mA input to correspond to
minimum (Zero) position.
MAXCMd - Maximum Split Range Command Select value
of 4 to 20 mA input to correspond to
maximum (Span) position.
bsRACT - Below Split Range Action
Action when command signal falls below the
minimum split range set value.
Options are as follows:
disabled
Close
open
stayput
go to position
bsRpos - Set Go to Position when command falls below
the minimum split range set value.
AsRACT
- Above Split Range Action
Action when command signal rises above the
maximum split range set value.
Options are as follows:
disabled
Close
open
stayput
go to position
AsRpos
- Set Go to Position when command rises above
the maximum split range set value.
9 ACTCfg - Actuator Configuration
ACT Typ
- Actuator Type
AT QT
- Quarter-turn Unit
AT RoT
- Rotary Unit
AT LIn
- Linear Unit.
This setting must match the configuration of the unit to
ensure correct operation.
ACT sIZ - Actuator Size
This parameter matches the Torque or Thrust
characteristic of the actuator model. For
example CMQ-500 lbf.in.
This setting must match the configuration of the unit to
ensure correct operation.
CAuTIon
enCInI - encoder Initiation.
This procedure is only necessary after replacement of
electronics assemblies or disassembly of the actuator drive
system. The Encoder
MusT be re-initialised before electrical
operation.
This procedure will remove Any previous travel limit
settings and characterisation settings.
Select the ENCINI menu and enter the Edit mode.
Use the UP or DOWN pushbuttons to move the actuator to
the centre position of travel.
Press ENTER to Re-Initialise the Encoder.
The travel Limits must now be Reset and any characterisation
parameters Re-installed.
STALL TIME
CPT 20
CMD SRCE
CPT 4
INFO
SPLT RANGE
RELAYS
ACT CFG
ADVANCED
CFG
Control Setup
INFO
ACT STS
AMP STS
TEMP
SWR VER
CTR SETUP
CTRLAL
IN DMP
LOS TO
LOS ACT
LOS LOW
LOS HI
RELAYS
RLY1 CFG
RLY1 POS
RLY1 FRM
RLY2 CFG
RLY2 POS
RLY2 FRM
ACT CFG
ACT TYPE
ACT SIZE
ENCOD IN
SP RANGE
MIN CMD
MAX CMD
BSRACT
ST CUST
LD CUST
DEFAULTS
LD FACT
POSIT
Position
SET PT
Setpoint
THRUST or TORQUE
Thrust Display or
Ouput Torque
LOCAL/REM
Local / Remote Operation
MANJOG
Manual Jog
TORQ/THRUST C
Close Torque/Thrust
TORQ/THRUST O
Open Torque/Thrust
CL ACT
Close Action
OP ACT
Open Action
BASIC
CL LIM
Close Limit (zero)
OP LIM
Open Limit (span)
CMD4
Field Command Signal4
CMD20
Field Command Signal20
DBAND
Deadband
FLTHST
Fault History Access
ADVANC
Advanced Menu
DEFLTS
Default Menu Access
STATUS
ASRACT
BSRPOS
ACT Cfg
spLT Rg
ACT Cfg - ACTuAToR ConfIguRATIon
ACT Type - ACTuAToR Type
ACT sIZe - ACTuAToR sIZe
enCod In - enCodeR InITIALIZATIon
STALL TIME
CPT 20
CMD SRCE
CPT 4
INFO
SPLT RANGE
RELAYS
ACT CFG
ADVANCED
CFG
Control Setup
INFO
ACT STS
AMP STS
TEMP
SWR VER
CTR SETUP
CTRLAL
IN DMP
LOS TO
LOS ACT
LOS LOW
LOS HI
RELAYS
RLY1 CFG
RLY1 POS
RLY1 FRM
RLY2 CFG
RLY2 POS
RLY2 FRM
ACT CFG
ACT TYPE
ACT SIZE
ENCOD IN
SP RANGE
MIN CMD
MAX CMD
BSRACT
ST CUST
LD CUST
DEFAULTS
LD FACT
POSIT
Position
SET PT
Setpoint
THRUST or TORQUE
Thrust Display or
Ouput Torque
LOCAL/REM
Local / Remote Operation
MANJOG
Manual Jog
TORQ/THRUST C
Close Torque/Thrust
TORQ/THRUST O
Open Torque/Thrust
CL ACT
Close Action
OP ACT
Open Action
BASIC
CL LIM
Close Limit (zero)
OP LIM
Open Limit (span)
CMD4
Field Command Signal4
CMD20
Field Command Signal20
DBAND
Deadband
FLTHST
Fault History Access
ADVANC
Advanced Menu
DEFLTS
Default Menu Access
STATUS
ASRACT
BSRPOS
spLTRg - spLIT RAnge opeRATIon
MInCMd - Minimum split Range Command
MAXCMd - Maximum split Range Command
bsRACT - below split Range Action
bsRpos - set go to position
AsRACT - Above split Range Action