Rolando Texart XT-640 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 156

background image

An Error Message Appears

6

FA

Q

143

raising the temperature. To continue waiting for the temperature to rise, press

. To start printing

immediately, press

.

[SERVICE CALL xxxx]

An unrecoverable error occurred, or part replacement that must be performed by a service

technician is required.

Note the number displayed on the display screen, then switch off the sub power. After you switch off the power,
inform your authorized Roland DG Corporation dealer or call center of the number that appeared on the display.

[SHEET TOO SMALL CONTINUE?]

The size of the data is larger than the printing area of the loaded media

To continue printing without correcting this, press

. At this time, the portion extending beyond the

printing area is not printed. To stop printing, stop sending data from the computer, and then raise the loading
lever. Make the printing area wider, for example, by replacing the media with a larger piece of media, and
then send the data again.

[SHEET SET ERROR SET AGAIN]

The loading lever was lowered while no media was loaded

Raise the loading lever, load the media in the correct position, then lower the lever again.



P. 21 "Loading Media"

[SHEET TYPE] is set to "OPAQUE," but transparent media was loaded

Raise the loading lever, set the [SHEET TYPE] menu item to “CLEAR,” and then reload the media.



P. 107 "Using Transparent Media"

The loaded media is too small

Press any button to clear the error. Replace the media with media of a usable size.

[DATA ERROR CANCELING...]

Printing was stopped because a problem was found in the data received.

Operation cannot be continued. Check for a problem with the connector cable or the computer, and redo the
operation from the step of loading the media.

[CLEANING ERROR]

Light choke cleaning was stopped due to some kind of operation.

The operation cannot be continued. Switch the sub power off by holding down the switch for one second
or longer, and then switch the sub power back on again. Afterward, redo light choke cleaning from the start.



P. 69 "Light Choke Cleaning"

[CANCELED FOR PUMP PROTECTION]

The printer made an emergency stop because the following state has continued for 10

minutes or longer while cleaning (normal, medium, powerful, light choke cleaning, subtank

refresh, or automatic cleaning while sub power was switched off) was in progress or during

the first ink filling procedure for the machine.



The printer is out of ink.

Operation cannot be continued. Switch off the sub power. After you switch off the power, contact your au-
thorized Roland DG Corp. dealer.

«
...
143
144
145
146
147
...
»

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Texart XT-640

Бренд: QMS Страницы: 2

Donation Point Even

Бренд: Quest Payment Systems Страницы: 2

Бренд: BART-TECH 3D Страницы: 34

Бренд: NEC Страницы: 7

Daisy Wheel 410

Бренд: Radio Shack Страницы: 140

Бренд: Olivetti Страницы: 246

Бренд: Savin Страницы: 4

Бренд: Jolimark Страницы: 64

EasyCoder PL-Series

Бренд: Intermec Страницы: 220

Бренд: Liene Страницы: 64

Бренд: Brother Страницы: 174

Spinwriter 5500B

Бренд: NEC Страницы: 19

SuperScript 150C

Бренд: NEC Страницы: 102

SuperScript 100C

Бренд: NEC Страницы: 71

SuperScript 4200

Бренд: NEC Страницы: 72

SuperScript 1450

Бренд: NEC Страницы: 113

SuperScript 4600N

Бренд: NEC Страницы: 121

SuperScript 4200N

Бренд: NEC Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды