Rolando Texart XT-640 Скачать руководство пользователя страница 82

Страница: 82 / 156

Maintenance That Should Be Performed Every Six Months

Maintenance

Finish refreshing the subtanks.



Install all the ink pouches.

Take care to use the right colors.

Attach the stoppers.

Take care not to crush the ink pouches.



Press



Raise all the ink pouch holders.

Raise the ink pouch holders slowly without letting
go of them.



Press



When the screen on the left is displayed, remove the drain

bottle and discard the discharged fluid.



Press

When finished, the screen shown on the left appears again.



Press

to go back to the original screen.

SET INK POUCH
12345678

UP INK POUCH
12345678

When installing an ink pouch and returning the
ink pouch holder to its original position, raise the
ink holder firmly until it clicks into place. Ink will
leak if the ink pouch holder is not returned to the
correct position.

EMPTY

DRAIN BOTTLE

INK CONTROL
REFRESH SUBTANK

Hold here

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды