Rolando Texart XT-640 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 156

background image

97

4

Advanced

Functions

Using the Dryer

What is the Dryer?

This machine is equipped with a dryer for drying the ink. You can adjust the temperature settings to match
the type of media and the printing speed.

WARNING

Caution: High temperatures

The dryer becomes hot. Exercise caution to avoid fire or burns.

WARNING

Remove any loaded media or switch off the sub power when printing is

not being performed.

The continued application of heat at a single location may cause fire or produce

toxic gases.

WARNING

Never use media that cannot withstand the heat.

Doing so may result in fire or the release of toxic gases or may degrade the

media.

WARNING

Never use the platen or dryer for any purpose for which they are not

intended, such as to dry clothing.

Doing so may cause overheating, resulting in a fire or accident.

Use the machine in an environment with an ambient temperature of 20 to 32°C (68 to 90°F).

If the machine is used at an ambient temperature lower than 20°C (68°F), then depending on the type or
width of the media, wrinkling or temperature-caused unevenness may occur. If this happens, try lowering
the temperature of the dryer by about 2°C (36°F). To obtain stable printing results, however, use the machine
in an environment with an ambient temperature of 20 to 32°C (68 to 90°F).

Note: Depending on the printing conditions, an external heater may be needed. For the details of the rec-

ommended external heater, contact your authorized Roland DG Corp. dealer. For information on how to
use the external heater, refer to the documentation for the heater you are using.

Dryer

This is used to speed up

the drying of the ink.

«
...
97
98
99
100
101
...
»

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Texart XT-640

Бренд: Lanier Страницы: 265

imagePROGRAF GP-540

Бренд: Canon Страницы: 82

Бренд: TallyGenicom Страницы: 166

Бренд: Lanier Страницы: 6

IMAGE M4100 Series

Бренд: G&G Страницы: 147

Phaser 6700V/DX

Бренд: Xerox Страницы: 162

B-470-QQ Series

Бренд: TEC Страницы: 32

Бренд: Agilent Technologies Страницы: 2

Бренд: Ricoh Страницы: 177

da Vinci 2.0 Duo

Бренд: XYZ Printing Страницы: 25

Бренд: MostFun Страницы: 25

Бренд: Brother Страницы: 378

Бренд: Brother Страницы: 107

Бренд: Brother Страницы: 10

Бренд: Brother Страницы: 11

Бренд: Brother Страницы: 74

Бренд: Brother Страницы: 3

Бренд: Brother Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды