Rolando Texart XT-640 Скачать руководство пользователя страница 45

Страница: 45 / 156

Setup of Media

Basic

Operation

Set the dryer temperature.

Press

to set the temperature.

Recommended temperature: 40°C

Press

to confirm your entry.

For the individual setting method and the description of this setting item, refer to the following section.



P. 98 "Setting the Temperature of the Dryer"

Adjust the print head height.



Press

to select [CHANGE].

Press

to confirm your entry.



When the screen shown on the left is displayed, open

the front cover.



Move the height-adjustment lever to adjust the print head height.

When the lever is moved to the "High" direction, the buzzer sounds twice. When it is moved to the "Low"
direction, the buzzer sounds once.

DRYER

30゜C 40゜C

To cancel setup

Procedure



Press

during setup.



Press

to select [YES].

Press

The screen shown in the figure on the left appears again.
Selecting [NO] returns you to the screen that was dis-
played when you pressed

QUIT SETTING
[YES] NO

MEDIA SETTING

HEAD HGT LOW
[CHANGE] NEXT

HEAD HEIGHT
LOW LOW

Normally move the height-adjustment lever to "Low." For media that is wrinkled or comes loose from
the platen, move the height-adjustment lever to "High."

Height-adjustment lever

Move firmly, until it stops.

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды