Rolando Texart XT-640 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 156

background image

Maintenance That Should Be Performed Daily

3

Maintenance

65

Cleaning

WARNING

Never use gasoline, alcohol, thinner, or any other flammable material.

Doing so may cause a fire.

CAUTION

Before attempting cleaning, switch off the sub power and wait until the

platen and dryer cool (approximately 30 minutes).

Sudden movement of the machine may cause injury, or hot components may
cause burns.

Wipe away any ink or grime on the media path and other areas as part of the daily cleaning procedure. Pinch
rollers, grit rollers, and the platen are particularly prone to the buildup of grime. Clean by wiping with a cloth
moistened with neutral detergent diluted with water then wrung dry.



This machine is a precision device and is sensitive to dust and dirt. Perform cleaning on a daily basis.



Never attempt to oil or lubricate the machine.

Wipe away any buildup of ink or

grime on the media path.

Grit rollers

Remove buildup of media and other material
using a brush. Never use a metal brush.

Pinch roller

Periodically wipe away any grime. Failure to clean
properly may result in the transfer of grime to the
surface of media.

Separating knife roller

This part is prone to paper dust buildup.
Periodically wipe the area clean. Failure to
clean properly may result in the transfer of
grime to the surface of media.

«
...
65
66
67
68
69
...
»

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Texart XT-640

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 117

Бренд: Oki Страницы: 45

Бренд: Oki Страницы: 112

Бренд: Oki Страницы: 115

Бренд: Oki Страницы: 2

Бренд: IBM Страницы: 16

Бренд: EasyThreed Страницы: 15

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 192

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 15

WORKCENTRE 7425

Бренд: Xerox Страницы: 88

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 33

C123 Copycentre

Бренд: Xerox Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды