Rolando Texart XT-640 Скачать руководство пользователя страница 8

Страница: 8 / 156

Machine

Highlights

Part Names and Functions

Printer Unit

Front

Back

Front cover

Leave closed except when loading

media etc.

Ink pouch holder

This is where ink pouches are installed.

Right cover

Remove this when

performing mainte-

nance.

Operation panel



P. 8 "Operation Panel"

Drain bottle

Loading lever (front side)

Operate this when you load media.

Left cover

Remove this when

performing main-

tenance.

Feed adjuster (front side)

Subtank slots

This is where subtank

cartridges are installed.

Main power switch
Power-cord connector

Ethernet connector

This is used to connect the machine to a network.

Status LED

This indicates the status of the machine’s network
feature. It lights up green when status is normal.

Activity LED

This flashes in yellow while data is
being received from the network.

Shafts

Loading lever (rear side)

Operate this when you load media.

Media holder

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды