Rolando Texart XT-640 Скачать руководство пользователя страница 141

Страница: 141 / 156

Other Problems

139

Cannot Cut Off the Media

Is the separating knife installed?

If the separating knife is not installed, you cannot cut off the media.



P. 89 "Replacing the Separating Knife"

Is the cut rail installed?

If the cut rail is not installed, you cannot cut off the media. The cut rail is removed when performing manual
cleaning. If the cut rail is not installed, remove the left cover, and then install the cut rail by following step



in P. 77 "Reattach the left and right covers, and finish manual cleaning mode.". After installing the cut rail,
be sure to attach the left cover.

Dryer Does Not Become Hot

Is the media loaded?

The media heating system does not warm up to the set temperature when

is off (by default). Load

the media and wait for the machine to warm up.



P. 97 "Using the Dryer"

Is the temperature of the room too low?

Use the machine in an environment where the temperature is 20 to 32°C (68 to 90°F).

It Is Not Possible to Check the Amount of Discharged Fluid in the Drain Bottle

Is ink splattered around the inside of the drain bottle?

If ink is splattered around the inside of the drain bottle, it may not be possible to check how much discharged
fluid the bottle contains.



P. 64 "If It Is Not Possible to Check the Amount of Discharged Fluid in the Drain Bottle"

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды