Rolando Texart XT-640 Скачать руководство пользователя страница 91

Страница: 91 / 156

Replacing Consumable Parts

Maintenance

Replacing the Separating Knife

If the separating knife becomes dull, replace it with the included replacement knife.

CAUTION

Be sure to perform operations as specified by the instructions, and never

touch any area not specified in the instructions.

Failure to observe these instructions may cause the machine to move suddenly,
resulting in injury.

CAUTION

Do not touch the edge of the separating knife.

Doing so may result in injury.

Enter the knife replacement menu.



Remove any media.



Press



Press

several times until the screen on the left

appears.

Press



Press

several times until the screen on the left

appears.

Press



Press

several times until the screen on the left

appears.

Press

The print-head carriage moves to a location where knife replacement
is possible, and then the screen shown on the left appears.



Open the front cover.

Preparations are complete when this screen appears.

Required Items

MENU
SUB MENU

SUB MENU
MAINTENANCE

MAINTENANCE

REPLACE KNIFE

NOW PROCESSING..

OPEN FRONT
COVER

FINISHED?

Replacement blade

for separating knife

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды