Rolando Texart XT-640 Скачать руководство пользователя страница 139

Страница: 139 / 156

137

Other Problems

The Machine Does Not Move

Are the cables connected?

Connect the cables securely.



"Setup Guide"

Is the power switched on?

Switch on the machine's main power, then press the sub power switch and make sure the sub power switch
lights up.



P. 20 "Switch On!"

Is a cover open?

Close the front, left, and right covers.

illuminated?

Printing is not performed when

is not illuminated. Lower the loading lever.



P. 52 "Getting Ready to Receive Data from a Computer"

Is the top menu displayed?

Top menu

If the top menu is not displayed, printing does not start even when data is sent from the computer. To go to
the top menu, press

, and then press



P. 52 "Getting Ready to Receive Data from a Computer"

Is a message displayed on the screen?



P. 140 "A Message Appears"

P. 142 "An Error Message Appears"

illuminated?

When

lights up, operation is paused. To resume, press

goes dark and printing

resumes.



P. 54 "Pausing or Canceling Printing"

W1200mm

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды