Rolando Texart XT-640 Скачать руководство пользователя страница 57

Страница: 57 / 156

Print

Basic

Operation

Cutting Off the Media

Procedure



Remove the left and right media clamps.



Close the front cover.



Check that

is lit.



Hold down

for one second or longer.

The media is cut off.

It is possible to configure the settings in the software RIP for automatic media cutoff after printing has
finished. For information on how to configure the settings, refer to the documentation for the software
RIP you are using.

Lift the media clamps

up to remove them.

Reflective tape

Knife guide

Printed area

The media is fed out toward

the front of the machine.

The media is cut off at this position.

Содержание Texart XT-640





























































































































































Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды

Rolando Texart XT-640, Руководство пользователя

Результаты поиска

Содержание Texart XT-640

Отзывы:

Похожие инструкции для Texart XT-640

Бренды по названию

Популярные бренды