Rolando Texart XT-640 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 156

Rolando Texart XT-640 Скачать руководство пользователя страница 71

69

3

Maintenance

If Colors Are Uneven

Mixing the Ink by Shaking the Ink Pouch

If ink components precipitate in the ink pouch, colors may
be uneven (unevenness in printed colors). If colors are
uneven, remove the ink pouches and shake them gently.

If uneven color issues are not resolved even after shaking the ink pouches, perform light choke cleaning.

Light Choke Cleaning

If printing is not performed for several days, printed colors may become unstable or uneven, e.g., when color
density is inconsistent, even if the same data is printed with the same settings. In such cases, perform light
choke cleaning. This will stabilize printed colors by agitating the ink.

Procedure



Press

.



Press

several times to display the screen shown

on the left.

Press

.



Press

several times to display the screen shown

on the left.

Press

.



Before shaking an ink pouch, wipe off any ink from around the mouth of the ink pouch.

If you do not wipe off the ink, it may splatter when you shake the ink pouch.



When you have finished agitating the ink, reattach the ink pouch immediately.

Taking time to reattach the pouch will adversely affect the ink path.



When installing an ink pouch and returning the ink pouch holder to its original posi-

tion, raise the ink holder firmly until it clicks into place.

Ink will leak if the ink pouch holder is not returned to the correct position.

Light choke cleaning consumes a lot of ink, and overly frequent use may damage the print heads them-
selves. Avoid performing more than necessary.

MENU
SUB MENU

SUB MENU
INK CONTROL

«
...
69
70
71
72
73
...
»

Содержание Texart XT-640





























































































































































Отзывы:

Нет отзывов