ROJ PCS 200 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 112

background image

Maintenance and Troubleshooting

- 4.8 -

PCS 200 Kit

Removing the MD from the machine configuration

In case a spare MD is not available and if the faulty MD is not able to communicate
with the CAN line, it is possible to remove the device from the machine configuration
in order to proceed with the job.

This requires a consequent change of the machine configuration as well as a change
of the devices logical address.

If this problem arises the 1-1801

“

Invalid configuration or MD address

” alarm

is

displayed when turning on the system, without changing any settings or MD
connections.

1.

Check the integrity of the fuse for the MD which is not able to communicate.

If the fuse is blown, replace it.

2.

Check the integrity of the CAN connection towards and from the faulty MD.

3.

If the problem persists, disconnect the system from the power supply via the

battery disconnect switch.

4.

Remove the fuse for the faulty MD but do not unplug the cable from the MD

as it is used to keep the CAN connection towards the other motors.

5.

Power up the system via the battery disconnect switch

6.

After the system has been started, a 1-1801

“

Invalid configuration or MD

address

” alarm

is displayed and an MD Addressing window is opened.

7.

Press the

“

Change configuration

”

button and modify the machine

configuration in order to show the number of devices after removing the
faulty one, and confirm the setting.

8.

Press the

“

Addressing

”

button

9.

Press a device icon to open the

“

Unaddress MD

”

window and select

“

All

MDs

”

10.

Go on addressing all the machine with the new configuration.

11.

Once the addressing has been completed, press the

“

Exit

”

button.

«
...
108
109
110
111
112
»

Содержание PCS 200

















































































































Отзывы:

Нет отзывов

Похожие инструкции для PCS 200

Бренд: Radio Shack Страницы: 52

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: ZIMO Страницы: 38

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: HAMTRONICS Страницы: 8

Бренд: jablotron Страницы: 2

Бренд: Samson Страницы: 20

Бренд: Kärcher Страницы: 4

Бренд: GEA Страницы: 47

Бренд: CAME Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды