ROJ PCS 200 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 112

ROJ PCS 200 Скачать руководство пользователя страница 109

Maintenance and Troubleshooting

PCS 200 Kit

- 4.7 -

Exchanging the faulty motor with another properly functioning motor already
mounted on the machine

If no spare MD is available, you can decide to exchange the faulty MD with another
motor mounted on the machine, in order to continue working (you can for ex.
exchange a faulty motor related to the seeding disc with the motor related to the
micro-granulator, in case this last function is not needed).

Warning!

: The following procedure requires that the motor having a failure is still

able to communicate via the CAN line. In case a 1-1801

“

Invalid configuration or MD

address

” alarm

is displayed when turning the machine on, even if the configuration

has been changed, you need to follow the procedure:

Removing the MD from the

machine configuration.

1.

Disconnect the system from the power supply via the battery disconnect

switch

2.

Disconnect the faulty MD cables from the MD to be exchanged, using a ¼

”

wrench.

3.

Remove the screws which fix the two motors and extract them from the

seeding disc shaft or the distributor shaft.

4.

Exchange their position, fix the motor in the new position and reconnect the

cables.

5.

Power up the system via the battery disconnect switch

6.

Make sure that no seeding job is active (in that case press STOP).

7.

Press the

“

MD addressing

”

button in the

“

Configuration

”

window to confirm.

8.

Press the

“

Addressing

”

button: all devices have been addressed.

9.

Press the faulty device icon and select

“

Unaddress MD

”

10.

Press the icon of the exchanged motor and select

“

Unaddress MD

”

11.

The icon corresponding to one of the exchanged MDs starts flashing

indicating that it has to be addressed.

12.

Close the MD safety switch on the correct position to address the device.

13.

The icon corresponding to the other MD starts flashing indicating that it has

to be addressed.

14.

Close the MD safety switch on the correct position to address the device.

15.

Once the addressing has been completed, press the

“

Exit

”

button.

«
...
107
108
109
110
111
...
»

Содержание PCS 200

















































































































Отзывы:

Нет отзывов