RITZ ICO 245 Скачать руководство пользователя страница 34

Страница: 34 / 50

Fault

Possible cause

Remedy

No measurement signal

Connecting cable loose

Check the secondary terminals,

Chapter 2.3.1

Damaged transformer

Check transformer and replace if
necessary

Faulty measurement signal

Incorrect frequency

Frequency according to

Rating

plate

Connections connected wrong
way round

Arrange connecting cables cor‐
rectly

Damaged transformer

Check transformer and replace if
necessary

Thermal stresses of the primary
screw fitting

Loose screw on the primary con‐
nection

Check the primary connection,

Chapter 2.3.1

Thermal stresses of the primary
screw fitting

Insufficient cross-sections of the
busbars

Use bus bars with a larger cross-
section,

Chapter 2.3.1

Thermal stresses of the secon‐
dary screw fitting

Loose screw on secondary clamp Check the secondary terminals,

Chapter 2.3.1

Insufficient cross-sections of the
connecting cables

Use connecting cables with a
larger cross-section,

Chapter

2.3.1

High voltage on the transformer
base

Incorrect assembly, the trans‐
former not earthed

Check the connections,

Chapter

2.3.3

Check the earthing measures,

Chapter 2.3.2

Limited device function through
overheating of the secondary
winding

Overload (the burden is higher
than the specified limit power)

Burden according to the informa‐
tion on the device's rating plate

Limited device function through
overheating of the primary
winding

Short circuit in the secondary
winding(s)

Contact the responsible sales
representative or the manufac‐
turer,

Chapter 7

Limited device function through
overheating of the primary circuit

Current-carrying connections not
screwed correctly

Check the connections according
to

Chapter 2.3.1

Damage to the high voltage insu‐
lation during operation

Leakage

Immediately interrupt the run‐
ning operation and contact the
responsible sales representative
or the manufacturer

Greatly increased partial dis‐
charges

ICO 72,5...245

USER MANUAL

When to interrupt the running operation

31/47

Содержание ICO 245



















































Результаты поиска

Содержание ICO 245

Отзывы:

RITZ ICO 245, Руководство пользователя, Страница: 34 / 50

Результаты поиска

Содержание ICO 245

Отзывы: