RITZ ICO 245 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

RITZ ICO 245 Скачать руководство пользователя страница 19

» Check the composite insulator for damage to and between the

insulator shields. If you notice any abnormalities, proceed as
described here:

Chapter 1.3.5 What should you do in the

event of damage? on page 10

» Clean the insulator if necessary. In this regard follow the

instructions as described under

Chapter 3.1.1 Cleaning the

device on page 24

3.

Check the oil level:
Check the transformer for oil leaks.
Check the oil level using the oil level indicator on the head of the
transformer (see Fig.). For further information please refer to

Procedure step 7 on page 26

1

Fig. 6: Position of the oil level indicator on the ICO type current trans‐
former
1 Oil level indicator

è

The oil level indicator should be in the green area.

4.

Prepare the transformer for connection on the primary side:
Always ensure a conductive contact at the primary connection
plates. If available, completely remove the protective coating (wax
emulsion) from the contact surfaces.

ICO 72,5...245

USER MANUAL
How to use this device as intended

16/47

«
...
17
18
19
20
21
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов