RITZ ICO 245 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 50

RITZ ICO 245 Скачать руководство пользователя страница 43

Type

ICO 72.5

ICO 123

ICO 145

ICO 170

ICO 245

Standard values
for insulation

Rated withstand AC
voltage (50 Hz/1 min.)

140 kV

230 kV

275 kV

325 kV

460 kV

Rated lightning impulse
withstand voltage
(1,2/50

m

s)

325 kV

550 kV

650 kV

750 kV

1050 kV

insulating class

E

Device-specific data
Deviating, customer-specific values are possible! For these speci‐
fications and other information required for operation of the trans‐
former (e. g. accuracy class, rated voltage, burden power, etc.)
please refer to the rating plate.

5.2 Environmental conditions

For deviating environmental conditions, see

Ò

Datasheet and

Ò

Rating

plate. Observe the following instructions:
» Never use the device in areas at risk of explosion.
» Never use the device near easily flammable materials.

Installation altitude

Up to 1000 m above sea level

1

1

This information refers to the standard version of the device. Modifica‐

tions for greater heights are possible. Please contact your sales partner
or get in touch with us directly

Chapter 7 Contact / customer service

Rated operating conditions

Temperature class

-25°C to +40 °C

ICO 72,5...245

USER MANUAL
Technical data

40/47

«
...
41
42
43
44
45
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов