RITZ ICO 245 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 50

RITZ ICO 245 Скачать руководство пользователя страница 16

2 How to use this device as intended

2.1 Important general safety instructions

2.1.1 Working disconnected from voltage

During operation, the transformer is live at high voltage. When con‐
nected and not earthed on the high-voltage side, the transformer may
be live at high voltage. This can cause personal injury, even in the
vicinity of the transformer. The following applies before all work on the
transformer, such as installation, maintenance and troubleshooting:
» Disconnect the source of high voltage.
» Safeguard against reconnection.
» Ensure no voltage is present.
» Earth the device.
» Cover or block off adjacent live parts.

2.1.2 Technically flawless condition of the transformer

External damage and improper handling or maintenance can impair
the operational safety of the transformer. There is a risk of accidents in
which people could be injured.

è

Only perform work on the undamaged transformer in accord‐
ance with these instructions!

2.1.3 Deviating operating conditions

Deviating operating conditions can impair the functionality and opera‐
tional safety of the transformer. This may cause personal injury.

è

Operation only if the information in

Chapter 5.1 Technical

data on page 39 and

Chapter 5.2 Environmental conditions

on page 40 is taken into account.

2.1.4 Structural changes

Structural changes can impair the functionality and operational safety
of the transformer. This can result in personal injury, as well as
damage to adjacent operating equipment.

è

Do not make any structural changes to the transformer!

ICO 72,5...245

USER MANUAL

How to use this device as intended

13/47

«
...
14
15
16
17
18
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов