RITZ ICO 245 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

RITZ ICO 245 Скачать руководство пользователя страница 18

2.3 Installation

2.3.1 Installing the device

Before you start the installation, think about your safety!

DANGER

High voltage in conductive components
There is danger to life through electric shock! Observe the
5 safety rules of electrical engineering.
» Disconnect the source of high voltage.
» Safeguard against reconnection.
» Ensure no voltage is present.
» Earth.
» Block off adjacent live parts.

1.

Connect the transformer mechanically to the switchgear:
» Maintain the insulation distance between system components

and live surfaces!

» If present, remove the transport protection. Do not make any

structural changes to the transformer

Chapter 2.1.4 Struc‐

tural changes on page 13.

» Ensure that the installation surface is even.
» Level out any unevenness between the transformer and the

installation surface.

» The position of the transformer during installation is upright.
» Secure the transformer to the foundation. For fixing dimen‐

sions please refer to the

Ò

Dimensional drawing. Depending

on the diameter of the drilled hole we recommend the fol‐
lowing bolt size:

Drilled hole

Æ

[

mm

]

Bolt size

18

M16

24

M20

» The required tightening torques are shown in the table, refer

to

Table on page 19:

2.

Ensure that the composite insulator is in perfect working order:

Fig. 5: Disconnect
mains!

ICO 72,5...245

USER MANUAL

How to use this device as intended

15/47

«
...
16
17
18
19
20
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов