RITZ ICO 245 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 50

RITZ ICO 245 Скачать руководство пользователя страница 38

WARNING

Danger to risk due to suspended loads
Loads can swing out and fall during lifting operations. This can
result in serious personal injury or death.
» Never stand under suspended loads or in their swing area.
» Only move loads under supervision.
» Only use approved lifting gear and sling gear with sufficient

load bearing capacity.

» Only use lifting gear that is in perfect working order.

Ensure that the environmental conditions for transport and storage are
met (

Chapter 3.4.2 Storing the device on page 37).

» Larger transformers are transported in a horizontal position.

Observe the information plate for transport on the terminal box of
the device.

» Place the transformer on the side facing away from the terminal

box on the air exclusion flange or the insulator flange (not on the
cover of the expanding vessel).

» Support the head of the transformer on vibration-reducing foam

and lash it to the transport frame.

» Screw the base of the transformer to a transport frame.

1.

Attach the lifting gear to the ring nuts on the base and the lifting
eye on the head housing,

2.

Bring the two lifting straps together in the middle and slowly lift
the transformer from the centre (Fig. 20).

3.

Lift the transformer one at a time.

Transporting and
lifting in a horizontal
position

Lifting the trans‐
former in a hori‐
zontal position

ICO 72,5...245

USER MANUAL

When to interrupt the running operation

35/47

«
...
36
37
38
39
40
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов