RITZ ICO 245 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 50

RITZ ICO 245 Скачать руководство пользователя страница 23

Make an electrically conductive connection between the earthing
bolts and the earthing point of the switchgear.

Ensure there is a clean potential connection at the earthing
connection.

è

The housing is earthed.

2.3.3 Connecting the device

Prepare the transformer for connection on the secondary side.
The secondary terminals are located in the terminal box at the trans‐
former base. Please refer to the

Ò

Dimensional drawing for detailed

information on the number and arrangement of the secondary termi‐
nals.

1

Fig. 10: Terminal box with secondary terminals
1 Secondary terminals

Also the secondary circuit diagram is located in the terminal box.
There is an aluminium plate on the underside of the terminal box to
which cable connections can be attached.

Observe the required tightening torques, see

Table on page 19

Establish access to the terminal area for electrical connection:
1.

Undo the locking screws on the terminal box.

2.

Remove the terminal box cover.

ICO 72,5...245

USER MANUAL
How to use this device as intended

20/47

«
...
21
22
23
24
25
...
»

Содержание ICO 245



















































Отзывы:

Нет отзывов