Riello TAU 150 UNIT Скачать руководство пользователя страница 69

Страница: 69 / 72

TECHNICAL ASSISTANCE SERVICE

FAULT

CAUSE

SOLUTION

Heat exchanger dirty

- Clean the combustion chamber

Insufficient air/fuel flow to burner

- Check and adjust the burner

Incorrect boiler temperature

setpoint

- Check the temperature setting

The boiler does not reach its

temperature setpoint

Incorrect boiler temperature

setpoint

- Check correct functioning.

- Check the temperature setting.

- Check electrical wiring.

No water supply

- Check the vent and bleed valves.

- Check CH circuit pressure.

Burner locks out

Fumes escaping into the air

- Check that the burner body is clean

- Check that the flue pipes are clean

- Check the condition of the boiler seals

- Check the quality of combustion

There is a smell of fumes

Leaks from the supply circuit

- Check that all joints are tight and

that the pressure measurement

points are closed

There is a smell of gas

Air in the circuit

- Bleed the circuit

Pump malfunctioning

- Unseize the pump

- Change the pump

The boiler reaches the set tem-

perature but the radiators are

still cold

Содержание TAU 150 UNIT









































































Результаты поиска

Содержание TAU 150 UNIT

Отзывы:

Похожие инструкции для TAU 150 UNIT

Бренды по названию

Популярные бренды

Riello TAU 150 UNIT, Руководство по установке и обслуживанию

Результаты поиска

Содержание TAU 150 UNIT

Отзывы:

Похожие инструкции для TAU 150 UNIT

Бренды по названию

Популярные бренды