Riello TAU 150 UNIT Скачать руководство пользователя страница 20

Страница: 20 / 72

GENERAL

EXTENDED INFORMATION LEVEL 2: process values

Press the

key.

Press and hold both

keys for at least 3 seconds.

Press the

key.

Press one of the

keys until you reach the parameter you require.

Process values

Nr.

Characteristic

C 0

Reserved

Ionisation current

C 2

Fan speed

C 3

Fan control current (PWM)

C 4

Relative boiler heat output

C 5

Pump setpoint

C 6

Differential control

C 7

Reserved

C 8

Reserved

C 9

Reserved

EXTENDED INFORMATION LEVEL 3: assistance

Press the

key.

Press and hold both

keys for at least 3 seconds.

Press the

key twice.

Press one of the

keys until you reach the parameter you require.

Assistance

Nr.

Characteristic

d 0

Reserved

d 1

Two stage or modulating control setpoint (PID)

d 2

Current boiler setpoint

d 3

Room temperature setpoint

d 4

DHW setpoint

d 5

Maximum modulation in central heating mode

d 6

Maximum speed at maximum heating power

d 7

Reserved

d 8

Reserved

d 9

Reserved

Содержание TAU 150 UNIT









































































Результаты поиска

Содержание TAU 150 UNIT

Отзывы:

Похожие инструкции для TAU 150 UNIT

Бренды по названию

Популярные бренды

Riello TAU 150 UNIT, Руководство по установке и обслуживанию

Результаты поиска

Содержание TAU 150 UNIT

Отзывы:

Похожие инструкции для TAU 150 UNIT

Бренды по названию

Популярные бренды