Rheem TRITON Скачать руководство пользователя страница 12

Страница: 12 / 61

Condensate Trap (Included in the

Exhaust T)

With an efficiency of greater than

95%, this unit will create much

condensation inside the flue tubes.

The condensate trap allows for the

controlled evacuation of the

condensation to a local drain

. (See

local codes)

Igniter and Flame Probe

Provides spark to burner and

flame rectification response to the

controller.

Main Igniter Controller

The control provides outputs for a

blower motor, high voltage spark

igniter, gas valve, and nonvolatile

storage of fault history. The

control receives inputs from

temperature probe, pressure

switches, Flue gas temperature

sensor, high temperature limit

switches and senses flame. The

control makes 9 tries of 3 attempts

(total of 27 tries) for ignition. If no

ignition, the control waits for one

hour before re-attempting ignition.

LCD Display and User

Control Panel

Color LCD with touch sensitive

overlay for user interface. Displays

tank set point temperature,

operational state, and various other

operational characteristics of the

water heater.

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

Parts

Содержание TRITON






























































Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды

Rheem TRITON, Руководство по обслуживанию и тренингу

Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды