Rheem TRITON Скачать руководство пользователя страница 11

Страница: 11 / 61

Part Name

Description

Picture

Blower

This is a variable speed blower that is

matched to the Dungs gas valve. The

speed and function of the blower is

monitored by the main controller.

Gas Control Valve

The gas valve, by Honeywell, is

matched to the blower motor. Their

functions are controlled by the primary

controller.

Flue Gas Temperature

Sensor – Exhaust

Measures the temperature of the

combustion gases at the discharge

vent of the water heater.

This normally closed switch has a

trip setting of 160

Power Anode Controller

The power anode controller controls

the current flowing through each

anode. The anode system is

protecting the tank against corrosion.

The power anodes can be checked

through menu options under

“system” and check “tank health” to

see the power output of the anodes.

The closer to 100% power, the more

bare metal there is in the tank.

Anode controller has LED flash code

indicators to determine if there is

communication between the

controller and anodes. Anodes can be

unplugged if anode or wiring is

damaged.

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

Parts

Содержание TRITON






























































Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды

Rheem TRITON, Руководство по обслуживанию и тренингу

Результаты поиска

Содержание TRITON

Отзывы:

Похожие инструкции для TRITON

Бренды по названию

Популярные бренды