Rheem TRITON Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 61

background image

BACnet Configurations

Triton

Service Manual SVC1020T ; Rev 4

80 and 100 gallon chassis

• This will open ‘BACnet Settings’ and will list the BACnet MAC address, Baud rate, BACnet Config, Max

Master Address, and Device Instance

• Each item can be selected by touching the item on the screen. Once selected, changes can be made

The BACnet Facilitator will have the BACnet MAC Address. This does not come from us. If the caller is an end user,
he/she will need to contact a BACnet Facilitator.

The

Baud Rate

should only in very rare circumstances be adjusted. Rheem support does NOT under any

circumstances provide advice for this setting.

The BACnet config should always be left as MS/TP MASTER.

The Max Master Addr should always be left at 127 unless the BACnet Facilitator wants to change it. An end user
should never change this and Rheem support should never suggest it.

The device instance will also come from the BACnet facilitator. If the DI is 4194303, it is defaulting and not connected
to the network. The BACnet Facilitator will have to enter these numbers.

NOTE: Premium Triton units come with the wiring connector needed to connect unit to BACnet network.
THIS IS ONLY INCLUDED WITH PREMIUM MODELS.

NOTE: WE SHOULD ONLY ADVISE CALLERS WHERE TO GO TO ENTER/ADJUST THESE SETTINGS, AND
NEVER ATTEMPT TO PROVIDE THEM WITH THE CONFIGURATIONS.

5 8

«
...
56
57
58
59
60
...
»

Содержание TRITON






























































Отзывы:

Нет отзывов

Похожие инструкции для TRITON

Бренд: Haier Страницы: 2

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Navien Страницы: 157

Бренд: Navien Страницы: 2

Бренд: Navien Страницы: 4

Бренд: Quooker Страницы: 12

Бренд: DAB Страницы: 64

Бренд: Danfoss Страницы: 20

Бренд: Dancover Страницы: 7

Бренд: WilTec Страницы: 8

Бренд: Sencor Страницы: 10

Бренд: Zibro Страницы: 14

Бренд: Ashley Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды